Just How to Remove as well as Replace a Bath Tub.
Just How to Remove as well as Replace a Bath Tub.
Blog Article
What're your insights and beliefs on A Step-by-Step Guide to Installing a Bathtub?
Installing a bathtub isn't precisely rocket science, but it does need solid plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is likewise a reasonably tough project. If the old bathtub is easily accessible, the task can move speedily; if you need to open a wall surface to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Rather than hiring a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will aid you install a new bath tub in your bathroom if you have already gotten a new tub as well as do not need to alter the plan of your previous water pipes.
Your tools and also product checklist ought to consist of the following:
Planning for the Installation
Firstly, the supporting framework supplied with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the tub in the called for setting. The wooden boards are handy in equally spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bath tub up until the level checks out level.
To mount taps, fit all-time low of the furthest adaptable tap connector to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply as well as examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Fill the tub and likewise examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has been made use of at least when as this will certainly settle it right into its final setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines are in location in between the tap and the sink. Protect the faucet in position with the manufacturer supplied backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former kind needs to be attached to the tap ends first, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, creating the water to pass through the wall between the bath and the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in usage. The sealer can split relatively early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that entry on How to Install a Bathtub when doing a search on the search engines. Sharing is nice. Who knows, you could be doing someone a favor. Thanks a lot for taking the time to read it.
Explore Now Report this page